We offer a wide range of Led Aviation Obstruction Lights for Telecommunications Tower that has a weather proof body and can withstand shock and vibration. These lights are compact, sturdy and power saving. The lights provide a complete lighting solution for Telecommunication Towers etc. LED’s of this model are surrounded by a polycarbonate lens cover to increase the impact of LED light. The lights have an in-built photocell (LDR) sensor, which is useful if solar panels are not included in the system. These systems comply with ICAO (Type A & B) product design and performance.

Our lights are mounted on a series of high intensity, special LED’s that are specially designed for use where a light source with an extended life (1, 00,000). The omni-directional light distribution is arranged to obtain the maximum output. It is placed in the zone between 70 degrees above and 10 degrees below the horizontal with a maximum of candelas at 20 degrees above. The lights are wired up to a connector in a terminal box for easy mains wiring.  These can be available in twin versions as per the requirements of the clients. The flashing light unit is optional.

The lights are widely used across the airports and air routes for indicating obstructions that might be a danger to the aircrafts.

Features:

• Cat no. SIA – LED (low) 36pc led aviation obstruction light
• Corrosion-resistance aluminum casting body in red powder coated finish
• These have electronic (SMPS) circuitry for the LED’s
• The light source is protected by a clear polycarbonate lens cover fully secured to the body
• The SMPS electronic circuitry is suitable for 24V-48V D.C. operation
• 24/48 V DC is also available in all

SPECTRUM:

Low intencity obstruction lights. For use in the vecinity airports,and on air routes to indicate obstructions which may constitute danger to air craft.

SPECIFICATIONS:

• This is a single light unit employing a serious of high intensity special LEDs,and has been specially designed for use while a light source with a extended life (approx 100000 hours) is desirable. The omni directional light distribution is arranged so that the maximum light out put, is obtained in zone between 70 degree above and 10 degree below.
• The body is cooosian aluminum casting finished in aviation yellow epoxy paint finished and house of electriccuirtry of the LEDs. The light source is provided by a thick clear glass dome mounted on hinged cast bezel ringed secured to the body by means of three stainless steel bolts.
• The electronic circuitry is a suitable for 200/240 volts 50z. and is wired up to a connector block in a terminal box for easy mains wiring.
• The fixture is fully weather proof and designed for shock and vibration resistance, and strength for 2.5K.V. with against reverse voltages up to 1KV.

(TWIN VERSION ALSO AVAILABLE ON REQUEST FLASHING UNIT OPTIONAL/ PHOTOCELL CONTROLLER OPTIONAL

(As effort are made constantly to improve upon the design & Process of manufacture,the fittings suppliers may offer in details from the data herein)

• Protection : Weather proof IP 55 as per 2147
• Material of construction: Cast aluminium (L.M6)
• Transparent part : Clear glass dome
• Gasket : Neoprene
• Cable entry : ET 19 mm (at base)

LED Details:

No.of LEDs : 300 nos.

Colour : Red

Intensity of each LED : 250 - 300 mcd.

No.of Circuits : 5 in parallel

Total MACP : 80 - 90 Candela

Total power consumption : 15W at 230V

Max. Forward current : 150 mA

Insulation resistance : 100M ohm at 500V

PIV Protection: LED proctedinternallyagainst reverse voltage of upto 1KV

Earthing : Terminal provided.

SPECTRUM:                   Low intencity obstruction lights. For use in the vecinity airports,and on air routes to indicate obstructions which may constitute danger to air craft.SPECIFICATIONS:                    this is a single light unit employing a serious of high intensity special LEDs,and has been specially designed for use while a light source with a extended life                   (approx 100000 hours) is desirable. The omni directional light distribution is arranged so that the maximum light out put, is obtained in zone between 70 degree                       above and 10 degree below
                       The body is cooosian aluminum casting finished in aviation yellow epoxy paint finished and house of electriccuirtry of the LEDs. The light source is provided                   by a thick clear glass dome mounted on hinged cast bezel ringed secured to the body by means of three stainless steel bolts.                     The electronic circuitry is a suitable for 200/240 volts 50z. and is wired up to a connector block in a terminal box for easy mains wiring.                    The fixture is fully weather proof and designed for shock and vibration resistance, and strength for 2.5K.V. with against reverse voltages up to 1KV.
                   (TWIN VERSION ALSO AVAILABLE ON REQUEST)                    FLASHING UNIT OPTIONAL/ PHOTOCELL CONTROLLER OPTIONAL              (As effort are made constantly to improve upon the design & Process of manufacture,the fittings suppliers may offer in details from the data herein)

Features: 

Protection : Weather proof IP 565 as per 2147

Material of construction: Cast aluminium (L.M 6)

Transparent part : toughened clear,transpare,borosilicate hard glass.

Gasket : Endless neoprent.

Total weight: Less than 5Kg

Cable entry : ET 19 mm (at base)

LED Details:

Colour : Red

wiewing angle:All direction.

Total integrated Candela:2000+ candelas

Intensity of each LED : 250 - 300 mcd.

Total power consumption : 15W at 230V

Max. Forward current : 150 mA

Insulation resistance : 100M ohm at 500V

Earthing : Terminal provided.

Input voltage Fluctuation:Can with stand +25%

                          12/24/36/48V DC versionavailable.

SPECTRUM:

                   Low intencity obstruction lights. For use in the vecinity airports,and on air routes to indicate obstructions which may constitute danger to air craft.

SPECIFICATIONS:

                    this is a single light unit employing a serious of high intensity special LEDs,and has been specially designed for use while a light source with a extended life

                   (approx 100000 hours) is desirable. The omni directional light distribution is arranged so that the maximum light out put, is obtained in zone between 70 degree   

                    above and 10 degree below

                       The body is cooosian aluminum casting finished in aviation yellow epoxy paint finished and house of electriccuirtry of the LEDs. The light source is provided

                   by a thick clear glass dome mounted on hinged cast bezel ringed secured to the body by means of three stainless steel bolts.

                     The electronic circuitry is a suitable for 200/240 volts 50z. and is wired up to a connector block in a terminal box for easy mains wiring.

                    The fixture is fully weather proof and designed for shock and vibration resistance, and strength for 2.5K.V. with against reverse voltages up to 1KV.

                   (TWIN VERSION ALSO AVAILABLE ON REQUEST)

                    FLASHING UNIT OPTIONAL/ PHOTOCELL CONTROLLER OPTIONAL

  (As effort are made constantly to improve upon the design & Process of manufacture,the fittings suppliers may offer in details from the data herein)

Features: 

Protection : Weather proof IP 565 as per 2147

Material of construction: Cast aluminium (L.M 6)

Transparent part : toughened clear,transpare,borosilicate hard glass.

Gasket : Endless neoprent.

Total weight: Less than 5Kg

Cable entry : ET 19 mm (at base)

LED Details:

Colour : Red

wiewing angle:All direction.

Total integrated Candela:2000+ candelas

Intensity of each LED : 250 - 300 mcd.

Total power consumption : 15W at 230V

Max. Forward current : 150 mA

Insulation resistance : 100M ohm at 500V

Earthing : Terminal provided.

Input voltage Fluctuation:Can with stand +25%

                          12/24/36/48V DC versionavailable.